ReadyMadeRC
SKY SURFER RTF BRUSHLESS (1.4M)
| Wingspan | 1372mm (54 inch) |
| Length | 915mm (36 inch) |
| Flying Weight | 624g (22 oz) |
| Drive System | 2620 Brushless |
| Speed Controller | 20A |
| *NOTE | Current version uses bullet type connectors and not deans/t-connector types |
| Battery | 11.1V 1300mAh Li-Po (basic charger included) |
| *NOTE | Current version uses bullet type connectors and not deans/t-connector types |
| Control system | 4 CH 2.4GHz |
| Radio Control Range | 3000 |
*Note: There are people looking at what they are calling "version 1" and "version 2" of this plane. They really aren't version 1 or 2, but they are just different versions of this plane. Mine are what people are calling version 1, just as the pictures show. This is MUCH better for FPV since there is a ton of space inside the fuselage. The "version 2" planes ruined the usefulness for FPV by putting the servos and control arms inside the fuselage. The tubes for the control arms add strength to the fuselage in this version. My store is focused on FPV, so the equipment I carry will be what is best for FPV!, *Not to be distributed or linked to by other companies who like to take other people's work. You know who you are... :), Servos:, 4X 9g high speed micro, Requires:, , Note for beginner pilots: Although this plane is super easy to fly, it's a good idea to find local flying help from an experienced pilot. This can help with the small amount of assembly that is required and with the first flights. It's difficult to give support remotely when someone is totally new to the hobby, so the local help and help from,
RTF with pre-installed servos, brushless motor , ESC, and 2.4GHz ...ReadyMadeRC
CASTLE CREATIONS PHOENIX EDGE 75 BRUSHLESS ESC, 34V MAX. W/BEC
| MIN | 2S LiPo MAX |
Helis:, 500 class, Fixed wing:, .40 - .52, Input voltage:, Max continuous amperage at full throttle:, 75 amps*, BEC voltage (voltage regulator for powering radio and sevos):, User selectable choice from 5 to 8.4 volt output, BEC output amperage:, 5 amp peak**, Width:, 2.0" (50.8mm), Length:, 2.8" (71.9mm), Height:, 0.9" (23.2mm), Weight w/wires:, 4.0 oz (113.4g), Weight w/o wires:, 2.5 oz (70.9g), Programmability:, Fully programmable Castle feature set using Castle Link USB adapter (coupon for free Castle Link USB adapter included in package) and freely downloadable Castle Link Windows software., Connectors:, Battery and motor connectors sold separately, Tools needed for installation:, Soldering iron and solder to attach bullets to motor wires and battery connector to power wires., *RC HOBBY APPLICATION RATING: 75 amps for the duration of a single 5,000 mAh battery pack with the ESC in contact with a 5 mph airflow of 25C (77F) or cooler air. Controller temperature must never exceed 100C (212F). Exceeding current or temperature ratings may damage components and may shorten the life of the ESC. Always verify system current draw at full-throttle. Decrease load or increase airflow to decrease the ESC’s operating temperature.,
With the debut of the Phoenix Edge series of ESCs ...ReadyMadeRC
DJI 5.8GHZ VIDEO DOWNLINK (TRANSMITTER + RECEIVER)
The Wireless Video Link includes both transmitter (TX) and receiver (RX) modules, working in the ISM frequency band of 5.8GHz (5725-5865MHz). Analogue modulated video signals are sent wirelessly by the TX module to the RX module, and then the video signal will be demodulated and sent to a display. There are 8 wireless channels can be selected when you are using this product.These channels are:CH1-5705MHZ, CH2-5685MHZ, CH3-5665MHZ, CH4-5645MHZ, CH5-5885MHZ, CH6-5905MHZ, CH7-5925MHZ, and CH8-5945MHZ., The characteristics of this product are: small size, low power consumption and high sensitivity. The product can be used in many applications requiring wireless video communication. When it's used in the aero-modeling hobby, the Wireless Video Link TX will be mounted to the aircraftand the Wireless Video Link RX is connected to a display screen, allowing video signal wireless transmission,
The new DJI Downlink is specially designed to work with ...ReadyMadeRC
GAUI 330X-S QUAD FLYER KIT WITH SCORPION MOTORS
,
The 330X Quad-Flyer 330X was designed based on UAV , ...ReadyMadeRC
GAUI 330X-S QUAD FLYER KIT W/ SCORPION MOTORS W/O GU-344 GYRO
| 5. System Extensibility | can be used with GPS positioning system and navigation system on 330X without any change |
| *The actual of Cruise data with full payload(The safety flight time | 1332/170X75%=5.88min) |
| Gaui 330X Quadcopter | Part One |
330X was designed based on UAV , which emphasizes the advantages are:, 1. Flight Efficiency: Standard Battery (2S2000mAh) time of flight for more than 12min, with a high-capacity battery, the flight time will be more than 20 min or more (available spreadsheet calculation), 2. Excellent wind resistance: the efficiency and load of propeller are perfectly optimized, so the wind resistance will be better than general electric aircraft, 3. High stability: contains GU344 (three-axis stabilizing system) for the beginner or the FPV flying, it is a very stable Vehicle, 4. Additional payload capabilities: payload up to 700g (including battery), can freely install cameras and video recorder, and other general system, Videos of 330X:, ,
The 330X Quad-Flyer This version comes without the GU-344 Gyro, ...ReadyMadeRC
TWINSTAR FPV PAN/TILT POD KIT
| Manual | TwinStarPod.pdf |
When purchased with the pan/tilt kit, comes with a mounting plate that will fit many popular FPV cameras including:, RMRC-420, RMRC-420XV, RMRC-520, RMRC-LL600, KX131, KX171, KX191, IF Cam, SN777, SN555 and others, Note: careful routing of camera wiring is required to prevent binding during 180 degree or 360 degree operation., This kit will include:, , Note: for the "no servo" option, it is up to the customer to modify the assembly if required. The system was designed for HXT900 servos. Any other servo must be aligned properly for proper gear engagement., You'll need to supply:, ,
A TwinStar FPV pod that uses a custom mechanism allowing ...ReadyMadeRC
SKYWALKER FPV PAN/TILT POD KIT
| Manual | HERE |
When purchased with the pan/tilt kit, comes with a mounting plate that will fit many popular FPV cameras including:, , Note: careful routing of camera wiring is required to prevent binding during 180 degree or 360 degree operation., This kit will include:, , Note: for the "no servo" option, it is up to the customer to modify the assembly if required. The system was designed for TG9e servos. Any other servo must be aligned properly for proper gear engagement., You'll need to supply:, ,
An FPV pod for the SkyWalker that offers a custom ...ReadyMadeRC
RADIAN FPV PAN/TILT POD KIT
| Manual | HERE |
When purchased with the pan/tilt kit, comes with a mounting plate that will fit many popular FPV cameras including:, , Note: careful routing of camera wiring is required to prevent binding during 180 degree or 360 degree operation., This kit will include:, , Note: for the "no servo" option, it is up to the customer to modify the assembly if required. The system was designed for HXT900/TG9e servos. Any other servo must be aligned properly for proper gear engagement., You'll need to supply:, ,
A Parkzone Radian and Radian Pro FPV pod that uses ...ReadyMadeRC
EASY GLIDER FPV PAN/TILT POD KIT
| Manual | EasyGliderPod |
When purchased with the pan/tilt kit, comes with a mounting plate that will fit many popular FPV cameras including:, RMRC-420, RMRC-420XV, RMRC-520, RMRC-LL600, KX131, KX171, KX191, IF Cam, SN777, SN555 and others, Note: careful routing of camera wiring is required to prevent binding during 180 degree or 360 degree operation., This kit will include:, , Note: for the "no servo" option, it is up to the customer to modify the assembly if required. The system was designed for HXT900 servos. Any other servo must be aligned properly for proper gear engagement., You'll need to supply:, ,
An Easy Glider FPV pod that uses a custom mechanism ...ReadyMadeRC
SKY SURFER FPV PAN/TILT POD KIT (FITS BIXLER V1)
When purchased with the pan/tilt kit, comes with a mounting plate that will fit many popular FPV cameras including:, , Note: careful routing of camera wiring is required to prevent binding during 180 degree or 360 degree operation., This kit will include*:, , Other options include:, , Note: for the "no servo" option, it is up to the customer to modify the assembly if required. The system was designed for TG9e or HS-65HB servos. Any other servo must be aligned properly for proper gear engagement., You'll need to supply:, , Manual:, Sky Sufer Pod Instructions,
A Sky Surfer FPV pod that uses a custom mechanism ...ReadyMadeRC
EASY STAR FPV PAN/TILT POD KIT
| Manual | EasyPod |
When purchased with the pan/tilt kit, comes with a mounting plate that will fit many popular FPV cameras including:, , Note: careful routing of camera wiring is required to prevent binding during 180 degree or 360 degree operation., This kit will include*:, , Note: for the "no servo" option, it is up to the customer to modify the assembly if required. The system was designed for HXT900 servos. Any other servo must be aligned properly for proper gear engagement., You'll need to supply:, ,
An Easy Star FPV pod that uses a custom mechanism ...ReadyMadeRC
CAMERA PAN AND TILT KIT
| Manual | Pan/Tilt Module |
Note: careful routing of camera wiring is required to prevent binding during 180 degree or 360 degree operation., Comes with a mounting plate that will fit many popular FPV cameras including:, , Note: Currently the back plates are designed for the pan/tilt system being installed on top of the aircraft. If you plan on mounting the assembly inverted under the aircraft, some modifications to the back plate may be required., This kit includes:, , Note: for the "no servo" option, it is up to the customer to modify the assembly if required. The system was designed for the servo options listed below. Any other servo must be aligned properly for proper gear engagement., You'll need to supply:, ,
This is a stand alone pan/tilt FPV module that uses ...ReadyMadeRC
CAMERA CABLE 4-WIRE 6-PIN SUPER COMPACT TO IMMERSIONRC/FATSHARK
The wiring order on the camera connector as delivered will fit the following cameras directly:, RMRC-600XV (Old version), RMRC-700XV,
This is a super small 4-wire 6 pin camera lead ...ReadyMadeRC
CAMERA CABLE (4-WIRE,6PIN FOR OLD VERSION RMRC-700XV)
PLEASE NOTE: This cable feed the voltage directly, so if you're powering your system with a 12V battery and you have a 5V camera you need to use a regulator before the cable.,
This is a 4-wire camera lead with a 6 pin ...ReadyMadeRC
CAMERA CABLE (4-WIRE, FOR CAMERAS WITH AUDIO)
Directly compatible with the following cameras:, RMRC-600XV, RMRC-540, RMRC-480, RMRC-420 (not 420xv), PLEASE NOTE: This cable feed the voltage directly, so if you're powering your system with a 12V battery and you have a 5V camera you need to use a regulator before the cable.,
This is a 4-wire camera lead compatible with many different ...